TMS 5000: Long Standoff Non-Contact Thickness Gage |
Specifications: PERFORMANCE: =========== Accuracy: +/-0.00025" or +/-0.025% of the sum of the distances from the transducers to the target surfaces; whichever is greater for distances up to 5" +/-0.033% from 1.5" up to 4" and +/-0.05% thereafter. Repeatability: +/-0.05% of the distance from the transducers to the target Inspection Rate: Variable to 58 measurements per second Operating Range: 0.2" - 23.999" or 5mm - 609mm (Transducer to target) Thickness Range: 0.004" - 9.9999" in 0.0001 resolution mode 0.004" - 99.999" in 0.001 resolution mode 0.1mm - 99.999mm in 0.001mm resolution mode 0.1mm - 999.99mm in 0.01mm resolution mode Off-Axis Alignment: +/- 2.5 to 5 degrees depending on target size, material and range ELECTRICAL: ========= Input Power: 100 VAC, 50/60 Hz 120 VAC, 60 Hz 230 VAC, 50 Hz Maximum Power Consumption: 35 watts Standard Interfaces: Full duplex asynchronous RS-232C, 3-wire or RS-422A, 5-wire communications interface Baud Settings: 300, 600, 1200, 2400, 4800, 9600, 19200, none Word Length: 8 bit; 7 ASCII + 1 Parity Bit Parity: unused Stop Bit: 1 stop bit Line Status: disable 16 bit parallel binary output, TTL Compatible 3mA Source, 20mA Sink Optional Interface: Analog: 0-10 VDC or 4-20mA (up to 2500 Ohm load for 4-20mA) Selectable analog span: 00.00" to 99.9999" or 0mm to 999.9mm Incremental steps of voltage or current within span: 4096 steps MECHANICAL/ENVIRONMENTAL: ======================== Dimensions and Weight: Transducer: 5.5"H x 1.5"D .33lbs Controller: 12"H x 12"W x 7.5"D, 25 lbs Enclosure NEMA 13 Rated Industrial Air Hood: 11"H x 4.5"W x 4.0"D 5 lbs Air Fan/Filter: 110V, 15"H x 14"W x 15"D 20 lbs Temperature: Operating -20 to +50 C Noise Immunity: Acoustic: Filtered to eliminate noise spectrum of common industrial environments Electrical: Shielded for RF/EMI Humidity: 95% maximum Non-condensing Transducer to Controller Separation: Standard: 10'-30' Optional: 500' PROGRAMMABLE TRANSDUCER CONTROLLER: ================================== Display: 5 digit LED display on controller Programming: 2 momentary push button switches on controller provide local programming of parameters. Controller can also be programmed remotely via the RS-232C, RS-422A interface Signal Compensation: Continuous automatic calibration for temperature changes Sample Averaging: Programmable from 1 to 4095 samples per measurement Amplitude Filter: Programmable to filter measurements from vibrating or poorly aligned targets Run Mode: Programmable for free running or sample on command by switch or contact closure Relay Configuration: Programmable relay closure in or out of limit set points. Electromechanical SPDT rated 2A maximum, 60 VDC Relay Thickness Limit Set Points: Programmable high and low relay limit set points for selectable closure, normally-in or normally-out of limits in 0.01 inch increments Delay to Relay Closure: Programmable relay delay from 0.002 to 65 seconds in 0.002 second increments Relay Closure Interval: Programmable relay closure interval from 0.002 to 65 seconds in 0.002 second increments |
Platinum (PT 100) temperature sensors |
| |
AD-100 100 Ohm RTD Sensor. Built around a platinum 100 temperature sensor, made from a 100 Ω, .00385 alpha element. Tolerance +/- .12% at 0° C for the element only. | ||
IS-1PT Durable sensor usually used on outside diameter measurement applications. 18 month warranty. | ||
IS-2PT Highly durable sensor usually used on inside diameter applications. 18 month warranty. | ||
| IS-4PT Miniaturized ID sensor, 18 month warranty | ||
LW-1PT Low cost sensor for lower volume applications. | ||
LW-2PT Low cost sensor on spring flexure, primarily for lower volume applications. 6 month warranty. | ||
GS-1PT probe. Used to sense gage (ambient) temperature. 6 month warranty. | ||
GS-1APT with AD590 electronic sensor. Used to sense gage (ambient) temperature. 6 month warranty. | ||
GS-2PT Needle Probe (specify length when ordering) Part #: PT650327 | ||
| LG-1PT Gage Temperature Sensor w/Mounting Bracket Part #: PT900116 | ||
In-Process temperature sensors |
| |
| DS-1 probe. Diamond Series sensor. Highly durable, for in-process temperature sensing. See article In-Process. Sensor Part #: 650301-D |
| |
DS-1 probe interface board. Diamond Series sensor. See article In-Process. | ||
AD590 and Thermistor Workpiece/master and gage temperature sensors (compatible with Albion products) |
| |
IS-1 Durable sensor usually used on outside diameter measurement applications. 18 month warranty. | ||
IS-2 Highly durable sensor usually used on inside diameter applications. 18 month warranty. | ||
| IS-4 Miniaturized ID sensor, 18 month warranty | ||
LW-1 Low cost sensor for lower volume applications. | ||
LW-2 Low cost sensor on spring flexure, primarily for lower volume applications. 6 month warranty. | ||
GS-1T Thermistor probe. Used to sense gage (ambient) temperature. 6 month warranty. | ||
GS-1A with AD590 electronic sensor. Used to sense gage (ambient) temperature. 6 month warranty. | ||
GS-2 Thermistor Needle Probe (specify length when ordering) Part #: 650327 | ||
LG-1 Gage Temperature Sensor w/Mounting Bracket Part #: 900116 | ||
GS-1 mounting bracket. Mounts GS-1 to flat gage fixture surface. |
DLP Cinema:
DLP Cinema technology projects crystal clear, razor-sharp and lifelike images for the ultimate in picture quality. DLP Cinema technology delivers a true digital picture with incredible clarity and vibrant colors every show.
With DLP Cinema technology, there is no more color fading, jump and weave, scratching and dirt accumulation which are common problems that plague film. DLP Cinema offers a consistent image with no degradation over time. With DLP digital, moviegoers can see a movie in its original pristine condition, exactly the way the director intended it, whether they see it during the first or fifth week of the run.
Advantages:
DLP Cinema technology delivers crystal clear and lifelike images for the ultimate in motion picture quality. DLP Cinema technology delivers a true digital picture with incredible clarity and vibrant colors every show.

LABELS
- 3D TV (3)
- Cell Phone Projectors (1)
- Digital Cinema (1)
- DLP Cinema (6)
- News (1)
- Products (4)
- Projectors (11)
- Technology (19)
ARTICLES
-
▼
2010
(38)
-
▼
April
(38)
- DLP Home Theater Projectors
- DLP HDTV
- DLP Projectors for Business
- DLP Projectors for Education
- DLP Pico Cell Phone Projectors
- DLP Pico Handheld Projectors
- DLP Notebook Pocket Projectors
- DLP Cinema
- DLP Cinema Enhanced 4K
- DLP Multimedia Pocket Projectors
- DLP Cinema technology
- DLP 3D TV
- Rear Projection Module
- Da-View
- Acoustical Imager
- Cinema Contour
- Da-Snap
- Pro Imager Horizontal Masking System
- Pro Imager Vertical Masking System
- Multi-Mask Imager
- Dual Masking Electrol
- Tensioned Dual Masking
- Horizon Electrol
- Advantage Deluxe
- Tensioned Advantage Deluxe
- Tensioned Advantage
- Products
- Large Venue Projectors
- DLP Technology
- Projector Advantages
- Digital Cinema
- News
- Lcd/Led/Dlp Projectors
- 3D
- Master Style Mini
- Sensors
- Compensator
- TMS 5000
-
▼
April
(38)